AEM CD-7 Carbon Digital Dash Display


CD-7 Carbon Non-Logging/ Non-GPS Display


In addition to all of AEM’s CAN based products, AEM has available validated and confirmed CAN setups for the following 3rd party products. We currently have over 230 validated 3rd party applications, and supply a CD-7 Power Cable to simplify the installation of 3rd party devices with every CD Digital Dash Display. We have also developed 3rd Party Plug & Play Adapter Cables for certain applications, which are highlighted below and can be viewed on our Install Kits tab.
A 2-Way DTM Style termination receptacle plug will be needed to create an adapter harness if a Plug & Play Adapter Harness is not available. We supply DTM-style connectors that can be viewed on the the DTM-Style Connector kits page. The required 2-Way DTM-Connector Kit part number is 35-2620, and it can also be found on the Buy/Instructions tab.

Adaptronic M1200, M2000, M6000 ECUs
Adaptronic Modular series Plug-in ECUs
Autosport Labs, AnalogX 4 Channel Analog to CAN Module
BigStuff GEN4 Pro Xtreme ECUs
Bosch IMU 2-Axis Accel & Yaw Sensor
Edelbrock Pro-Flo 4 Electronic Fuel Injection
EFI Technology S.r.l. Euro-4 ECU
EMS EM-Tech EM70, EM80, EM140, EM160 & EM180 ECUs
gaugeART 31-001, 8 Ch Analog Expansion Module
GM/Delphi MEFI-4b ECUs
Haltech Elite 550, 750, 950, 1000, 1500, 2000, 2500, 2500T ECUs
Haltech Elite VMS, VMS-T
Haltech Platinum Pro, Platinum Sport and Platinum Sprint ECUs
Haltech WBC1 & WBC2, 1 & 2 Ch CAN widebands
Holley HP EFI, Dominator EFI ECUs CD-7 to Holley EFI Plug & Play Adapter Cable Available
Hondata KPro4 and S300 V3 ECUs
KMS Single Ch CAN wideband
KMS 4 Ch EGT Module
KMS 4 Ch Wheelspeed Module
KMS 2 Ch DBW Module
KMS Flex Fuel CAN Module
Life Racing F42, F88, F90 & GDI Series ECUs
Link G4+ based ECUs CD-7 to LinkG4+ ECUs Plug & Play Adapter Cable Available
Link CAN-Lambda Module
Megasquirt, MS3, MS2, Microsquirt, DIYPNP & MSPNP Gen2 ECUs
MicroTech LT-9C, LT-10C, LT-15C & LT-16C ECUs
Motec M1, M84, M400, M600, M800, & M880 ECUs
Motec PDM15, PDM16, PDM30 & PDM32 Power Distribution Modules
Motec PLM Lambda Module
Motec LTC, LTCD Lambda to CAN Modules
Motec E888, E816, CAN Expansion Modules
MSD AtomicEFI Throttle Body ECUs CD-7 to MSD Atomic TBI Plug & Play Adapter Cable Available
MSD GRID Programmable Ignition
PCS EGT-2000, 8 Ch EGT Module
Performance Electronics PE3 Series ECUs
Polaris RZR XP-900, RZR XP-1000, & RZR XP-Turbo ECUs
ProEFI Pro128, Pro112, and Pro48 ECUs
RaceGrade TC8, 8 Ch EGT Module
RaceGrade 8 Ch and 15 Ch Keypads
Racepak V300SD, V500SD, Sportsman, G2X, & G2XPro Loggers
Racepak 220-VM-USM, Universal 4 Sensor Analog Modules
Racepak 220-VP-IRXXXX, IR Tire & Brake Temp Modules
Racepak 220-VP-JBXXXX, Exhaust Temp Modules
Racepak 220-VP-PTXXXX, Pressure Sensor Modules
Racepak 220-VP-PTXXXX, Wheelie Bar Force Modules
Racepak 220-VP-RIDEHTXX, Laser Ride Height Modules
Racepak 220-VP-TCXXXX, Thermocouple Modules
Racepak 220-VP-TRXXXX, Coolant/Air/Oil/Trans/Diff Temp Modules
Syvecs S6, S6+, S6I, S8, SDI & S12 ECU’s
Techmor AC-1-4, 4 Ch Analog Expansion Module
Techmor IR-1 Non-Contact IR Tire Temperature Module
Techmor AP-1, 16 Ch Aero Pressure Sensor Module
Techmor SG-1-C, Strain Gauge Amplifier Module
Vi-PEC i44-i88 ECUs CD-7 to Vi-Pec i44/i88 ECUs Plug & Play Adapter Cable Available
Zeitronics Zt-3 CAN AFR Meter and Datalogging System
Zeitronics ECA CAN Ethanol Content Meter

Categories: ,


Full color 7” screen with 800×480 resolution
Direct sunlight readable (1000cd/m2 brightness and anti-glare filter)
Layout files interchangeable with all versions of the CD-5 Carbon
Wiring interface/harness is identical to the CD-5 Carbon
Rugged, lightweight flow-molded carbon fiber composite enclosure
Total display weight of 20.9 oz. / 595 grams
IP65 water resistance – open cockpit, marine and motorcycle safe
Accepts channels from two separate user programmable CAN bus connections – works with AEMnet enabled devices and non-AEM 3rd party devices side by side
Plug & Play Adapter Cables available for Holley, Link, MSD Atomic and Vi-Pec ECUs
Accepts channels from 2008-up factory ECUs using Plug & Play OBDII CAN Adapter Cable (PN 30-2217, sold separately)
Install the CD-7 Carbon on carbureted and pre-2008 stock ECU-equipped vehicles using a 22 Channel CAN Sensor Module (PN 30-2212, sold separately)
Available with or without 200Mb internal logging (up to 1,000Hz/channel)
Available with or without on-board 20Hz GPS receiver and antenna
Add a Vehicle Dynamics Module for GPS, 3-axis gyroscope and 3 axis accelerometer for G-loads, roll, pitch, yaw, track mapping and lap timing (PN 30-2206, sold separately)
Add an 8 Channel K-Type EGT CAN Module for 8 additional temps via AEMnet CAN bus (PN 30-2224, sold separately)
Seven programmable pages including four Main pages, Alarm, On-Change and Start-up pages
Dedicated Alarm page quickly identifies problems, programmable in almost any language! (user defined)
Unique On-Change page can be used to identify map switching for boost, traction, lap times, etc.
Use included page layouts and input your channels and text, or create your own from scratch
Free DashDesign Graphics Editor software
Seven LED RPM/shift light indicators on top of the housing (programmable and dimmable)
Two programmable LEDs
Odometer function
Over 200 supplied fully programmable SAE and custom warning icons, and you can add your own
‘Headlight-in’ connection dims the dash and LEDs during night operation
Two extra switch inputs included for displaying user-triggered events (blinkers, high beams etc.)
User supplied graphics can be changed based on channel values (up to the full screen size)
Convert CAN bus channel values to user-defined text in multiple languages


There are no reviews yet.

Be the first to review “AEM CD-7 Carbon Digital Dash Display”

Your email address will not be published. Required fields are marked *